Close

Heating Installation: Essential Things You Need to Know

Heating Installation: Essential Things You Need to Know

Heating Installation

Whether you are planning to replace your old heating equipment or install a new unit for your home, there are several things you should consider to make the process successful. Buying a new unit and paying for the professional installation can be costly, but it can become even more expensive if you fail to follow the right procedure. That is why it is always recommended to call the experts to handle this complex project. This may sound expensive upfront, but it will surely save you money in the long run.

This post is for you if you have a new furnace installation project soon. Keep reading to understand the things you need to know about heater installation.

Factors to Consider Before Installing a New Heating Unit

From energy efficiency to the cost of installation, many elements go into making the best choice for your home. Here’s what you need to know before installing a new heater.

Energy Efficiency

Regarding energy efficiency, all heating units are not created equal. Some systems use more energy than others, which can add up to monthly bills and the unit’s overall lifespan. Make sure you understand the energy efficiency ratings of each unit before making a decision. Consider options like heat pumps or geothermal systems if you’re looking for an efficient system.

Cost of Installation

The installation cost is another important factor when choosing the right heating unit for your home. Installation costs vary depending on the type of system you choose and its complexity. Make sure you get multiple estimates from different contractors before making a decision. It’s also important to compare warranties and ensure that any contractor you choose is licensed and insured in your state.

Maintenance Requirements

Most modern heating units require regular maintenance, like filter changes and annual tune-ups to keep them running efficiently and safely. Be sure to research the specific maintenance requirements for each system before deciding which one is right for your home. This will help ensure that your new system runs well over time and doesn’t require too much upkeep once installed.

Size Matters

Size matters when choosing the new heating system for your home. A unit that’s too small won’t be able to keep up with demand, while one that’s too large uses more energy than necessary (and can cause humidity issues). Make sure you get an accurate assessment of BTU (British Thermal Unit) needs from a qualified professional before making your final choice—it could save you money in the long run!

While replacing an old heating system with a brand-new one might seem daunting at first glance, it doesn’t have to be if you take some time beforehand to do your research and make an informed decision based on all factors involved.

Common Types of Heating Systems for Installation

Now that you know the factors you need to consider before getting a heater installation, it’s time to learn the different types of units available.

Many homeowners are switching to more efficient and cost-effective systems that can power their homes all winter long. Before making your decision, it’s important to understand what heating systems are available and their advantages and disadvantages.

Here are the five most common types of heating systems for installation.

Furnaces

The furnace is the most common type of heating system used in homes today. It is powered by gas or electricity and works by blowing hot air through a series of ducts throughout your home. Electric or gas furnaces typically has an efficiency rating between 80% and 98%.

One of the main advantages of a furnace installation is its low initial cost, but it does require regular maintenance to keep it running efficiently.

Boilers

A boiler works by circulating hot water through pipes throughout your home, thus providing heat to each room. Boilers are more energy-efficient than furnaces since they use less energy to heat water than air. Boilers also last longer than furnaces, although they require more frequent maintenance due to their complex design.

The main disadvantage of boilers is their high initial cost—they can be quite expensive upfront but may be worth it in the long run if you stay in your home for a while. 

Heat Pumps  

Heat pumps are one of the most efficient forms of heating available today as they use much less energy than other systems. They work by transferring heat from one area (e.g., outside) into another (e.g., inside) using refrigerant lines connected between two units (an outdoor unit and an indoor unit).

The main advantage of a heat pump is their high-efficiency rating (upwards of 300%). Still, they do require more frequent maintenance due to their complexity, as well as some additional costs for installation and repair if needed down the line.

Radiant Floor Heating  

Radiant floor heating works by circulating hot water underneath your floors, thus providing warmth directly from below rather than traditional radiators or forced-air registers found with other types of systems. This type of system tends to be very efficient since there are no air leaks or drafts, meaning that all the heat stays within your home rather than escaping through windows or doors like with other systems.

Radiant floor heating has a high initial cost but can save money on energy bills over time thanks to its excellent efficiency rating—upwards of 90%.

Geothermal Systems  

Geothermal systems are powered by underground loops that transport heated water into your home via a series of pipes connected to an indoor unit that circulates warm air throughout your space. These are some of the most efficient systems available today, with efficiency ratings upwards of 400%.

The downside is that geothermal systems require significant excavation work during installation and higher upfront costs compared to other types mentioned here—but these costs may be worth it in terms of energy savings over time!

Many different types of heating units are available for installation today, ranging from traditional furnaces and boilers to more advanced options like heat pumps and geothermal systems. Each type has its own set of advantages and disadvantages regarding energy efficiency, maintenance needs, cost factors, etc., so it’s important to research each option thoroughly before making a final decision about which one is best for you and your home’s needs!

Ultimately though, rest assured knowing that whatever choice you make should provide you with plenty of warmth throughout those cold winter months ahead!

Call Johnston’s Heating & Cooling for Quality HVAC Replacement Services

When you call Johnston’s Heating & Cooling for all your comfort needs, you call a company that cares about your budget and needs. We will consider many factors for this project, including energy efficiency, installation costs, maintenance requirements, and size! Doing so will ensure you get the most out of your new heating unit without breaking the bank or sacrificing comfort or safety in your home environment! We also provide air conditioning services.

Call us at (717) 504-2613 to get started with furnace replacement or heating repair.

Share this post

Have a Question?

Let us know how we can help